MemTest86 - тестирование оперативной памяти

[Dogmatist]

MemTest - это маленькая утилка для тестирования оперативной памяти. Для короткого тестирования достаточно 10-15 минут, для тестирования на надежность работы RAM - в районе суток.

Домашняя страница

[YSF]

MemTest86 V6.2.0 Free Edition (also includes V4 for old machines)

Изменения:

• Due to the high number of failures reported for the Hammer Test (Test 13), the algorithm was revised to perform 2 potential passes:
• Row pairs are hammered at the maximum hammer rate. (ie. no delays between each row pair hammer)
• Row pairs are hammered at a lower hammer rate (200K per 64ms, as determined by memory vendors as the worst case scenario)
• If memory errors are detected in the first pass, error details are not immediately displayed to the user and the second pass is started. If errors are detected in the second pass, they are reported as normal.
• If errors are detected in the first pass but not the second pass, a warning of potential high frequency bit flips is displayed to the user.
• The premise behind this revision is to better inform users of the significance of errors detected in the Hammer Test, as opposed to a strict PASS/FAIL result. Although errors detected in this test are real errors, the conditions needed to induce these errors occur only very rarely in normal PC usage, and should not be of concern to most users. Therefore, a warning rather than an outright failure would ensure the user is aware of the issue and be able to take the necessary measures to mitigate the issue.
• The details of the errors that were detected in the first pass of the Hammer Test but not during the second pass can be displayed in the report by specifying the configuration file parameter 'REPORTNUMWARN'. This parameter represents the maximum number of warnings to display in the report file.
• New configuration file parameter 'AUTOMODE' for full automation. Enabling this parameter shall result in the following:
• Splash screen is skipped and the tests are started immediately
• When the tests are completed, the report is saved to disk automatically
• System is rebooted
• Fixes/Enhancements
• Shortened the test time for Hammer Test (Test 13) by reducing the total number of hammers per row address pair
• Fixed issue with the main menu not displaying for certain EFI firmware. Due to the fact that many EFI firmwares require the use of the obsolete ConsoleControl protocol to switch between graphics/console mode, the graphics/console mode workaround is now enabled by default.
• Fixed bug with details of empty RAM slots being displayed when using SMBIOS memory device information
• Added Intel Skylake ECC support
• Updated Jedec manufacturer ID list for displaying the vendor name from RAM SPD. Fixed Jedec manufacturer ID lookup function to support > 7 continuation codes.
• Fixed AMD Hudson-2/Hudson-3 SMBus support to include various hardware revisions
• Various system info related updates/fixes (SPD, CPU)

Страница загрузки

Windows Downloads: Image for creating bootable CD (ISO format) (4,08 Мб) | Image for creating bootable USB Drive (5,79 Мб)

Linux/Mac Downloads: Image for creating bootable CD (ISO format) (4,08 Мб) | Image for creating bootable USB Drive (5,33 Мб)

[SerVer_UA]

MemTest86 V6.3.0 Free Edition (also includes V4 for old machines)

Изменения:

Version 6.3.0 27/Jan/2016
New Features
New configuration file parameters MINSPDS, SPDMANUF and SPDPARTNO to specify the values that the RAM SPD must match before allowing the tests to start. This may be useful for RAM manufacturers that need to verify that the SPD data has been programmed correctly.
New configuration file parameter SKIPSPLASH to skip the 10 second splashscreen and proceed directly to the main menu
New mode for the configuration file parameter AUTOMODE to specify that MemTest86 shall run the tests immediately (skipping the splashscreen and main menu) but prompt the user to save the results after test completion
New configuration file parameters ADDR2SLBITS and ADDR2CSBITS to specify the bit positions of a memory address to exclusive-or (XOR) to determine which DIMM slot/chip select (0 or 1) corresponds to the failure address
Fixes/Enhancements
Added ECC detection support for Broadwell-H chipset
Added ECC detection support for Broadwell-DE chipset
Added ECC detection support for AMD Bald Eagle (2nd generation Embedded R-series)
Added ECC injection support for AMD Steppe Eagle/Bald Eagle
Added SMBus (SPD) support for Broadwell-DE
Fixed decoding of JEDEC manufacture names from the SPD
DDR3 XMP rev1.3 SPD decoding is now supported
Fixed retrieval of DDR4 SPD bytes for Intel ICH SMBUS
Added workaround for buggy firmware when calls to EFI MPServices fail
Fixed MemTest86 freezing on network boot
Fixed bug with wrong details being displayed for detected memory warnings in the report file
Fixed bug with CPU type detection for older CPUs
Fixed benchmark chart not being displayed after running a RAM benchmark test when there is a failure in saving results to disk
Report file now includes the RAM serial number, if available
Various system info related updates/fixes (CPU)

Страница загрузки

Windows Downloads: Image for creating bootable CD (ISO format) (4,00 Мb) | Image for creating bootable USB Drive (5,57 Мb)

[SerVer_UA]

MemTest86 V7.1 5 Free Edition (also includes V4 for old machines)

Изменения

Страница загрузки

Windows Downloads: Image for creating bootable CD (ISO format) (4,45 Мb) | Image for creating bootable USB Drive (6,46 Мb)

[SerVer_UA]

MemTest86 V7.2 Free Edition (also includes V4 for old machines)

Изменения

Страница загрузки

Windows Downloads: Image for creating bootable CD (ISO format) (4,13 Мb) | Image for creating bootable USB Drive (5,77 Мb)

[SerVer_UA]

MemTest86 V7.3 Free Edition (also includes V4 for old machines)

Изменения

Страница загрузки

Windows Downloads: Image for creating bootable CD (ISO format) (5,03 Мb) | Image for creating bootable USB Drive (6,68 Мb)

[SerVer_UA]

MemTest86 V7.4 Free Edition (also includes V4 for old machines)

Изменения

Страница загрузки

Windows Downloads: Image for creating bootable CD (ISO format) (5,64 Мb) | Image for creating bootable USB Drive (8,21 Мb)

[SerVer_UA]

MemTest86 V7.5 (Build 1001) Free Edition (also includes V4 for old machines)

Изменения

Страница загрузки

Windows Downloads: Image for creating bootable CD (ISO format) (5,32 Мb) | Image for creating bootable USB Drive (7,81 Мb)